We finished the rough installations at the Cultured Cottage, which means the pretty part of the job has started. It also means that we’ve spent weeks on shop drawing review. On a house that can't lean on square footage, one wrong inch in a drawing turns into a problem in the finished room. Here is who checked what, what we argued about, and what the rest of the finishing phase has asked of us.
Shop Drawing Review for a Custom Home Needs Every Team Member at the Table
A shop drawing is a close look at one custom fabricated element: the general contractor, the architect, and the interiors firm each read it from different perspectives. We covered these basics earlier in the series.
I read them for clearances. I want to know the appliances we specified are the right ones and that they will fit. Spec sheets give you the dimensions of the unit, but may leave out the two to three inches you need to plug it in, which matters with a counter depth fridge in a kitchen that has no room to move. The interiors team reads for transitions. Does one material meet the next with a miter or a bevel? How does the stone meet the cabinetry or a corner cabinet? The architects look at the same drawing from a higher level and ask how each piece works with the design intent.
The best projects have healthy tension between those three perspectives. I believe that, if you don't have some healthy tension going on, then no one's invested enough.
The Kitchen Came Down to Symmetry and Centering
Our kitchen debate had two parts, and both were about symmetry and centering. The interiors team was leaning into a European eclectic look, and the architects love symmetry. The upper cabinets beside the range and the position of the island both had to be settled in the shop drawings.
The uppers flanking the range are glass, stained to contrast with the painted cabinets around them. The range doesn't sit exactly centered on that wall, so the uppers came out asymmetric. Making them symmetrical would have meant adding a corner cabinet on the window wall, which gives us one more closed cabinet and also puts a corner on that wall. Leaving them asymmetric makes the uppers look more grand and keeps the same amount of cabinetry. The tradeoff is that there's no base cabinet underneath for an appliance garage, and everything is exposed, so you can't merely throw stuff inside. The island raised a similar question. With the range slightly off center, do we center the island with the range or with the dining room windows?
Tile Layout Planning Starts with the Grout Line
Tile looks simple until you ask how it ends. We wanted full tiles across our walls with no thin cuts to make up a shortfall, so we needed to know the tile layout early. Grout line size and the way the tile terminates both change the look and the price.
Grout lines can be a sixteenth, an eighth, a quarter, or even a half inch for something like a Moroccan zellige. At a sixteenth or an eighth of an inch, you generally can't use sanded grout, and sanded grout is what you want in a wet area like a bathroom. A tight line with a robust grout means epoxy grout, and epoxy grout is more expensive.
Then you decide where the tile ends. If it terminates into the wall, the Durock or drywall outside the shower has to protrude so the tile can come up to it. A polished edge needs no transition, though that tile is probably going to cost more. A lot of people use Schluter transitions, which come in all kinds of colors. A matching bullnose works if the tile manufacturer makes one, and bullnose and Schluter differ in both labor and material cost. A tile mistake is very visible and very hard to fix, and tile layouts are a big source of scope creep.
Floor Heat Adds Height
Floor heat in a bathroom adds more height than one might expect. Our primary bath has a heated floor and the primary bedroom has hardwood, and we didn't want anyone stepping up from one into the other.
If you're heating one floor, you'll probably use electric floor heating under the tile. In our experience, a traditional electric install needs at least a quarter inch and, really, a half inch by the time it's done. The membrane on the subfloor might be an eighth of an inch thick, and the mortar adds another eighth to a quarter inch. The mortar also has to cure, so everyone comes back another day before the wire goes in and the tile goes on top.
On this project I tried QuietWarmth from MP Global Products, which I had seen at a conference. You roll it out like a mat. It comes with the wiring already in it, it needs no mortar, and it's no thicker than a credit card. With other electric systems we run two wires because, if any part goes out, the whole thing goes out. With this product, one puncture only takes out one section. I'm a fan.
The Finishing Phase Runs in a Straight Line
During rough installations, roofers, siding installers, plumbers, electricians, and HVAC crews can all be on site at once. It feels very high energy and productive. Finishing, however, is sequential. One trade comes after the next. We insulate before we drywall. Hardwood goes down before baseboards. Paint and stain is a multi-phase process on its own: right after drywall, we lay the hardwood flooring and leave it rough, with no stain, because too many people are walking on it. Once the moldings and doors are in, we do the first round of paint. Prep is where the time goes, and it's why a paint bid often surprises people.
So, one can conclude that the real test of a builder is not whether or not they can install the interior doors, it’s whether or not they foresaw that the interior doors needed to be ordered. A project sitting in silence waiting on a delivery leaves everyone else, and the schedule, waiting too.
Remember the cardinal rule: in construction, it’s never “just” anything.
Watch the full episode here to hear me walk through the kitchen, tile, and floor heat decisions. If you're joining partway through, the Cultured Cottage Series playlist starts at the beginning.
Frequently Asked Questions
What does shop drawing review catch?
It catches clearances, like the two to three inches behind an appliance for its plug, along with how materials transition and how each piece fits the design intent. A shop drawing is a deep dive into one custom fabricated element, such as the kitchen cabinets or metalwork, so the team can check it before it gets built.
Who should be part of shop drawing review for a custom home?
The general contractor, the architect, and the interiors firm. The contractor checks clearances, the interiors team checks how materials transition, and the architects check the design intent.
Why does tile layout planning need to happen early?
Custom luxury demands full tiles across the walls with no thin cuts, which depends on knowing the tile and grout line size ahead of time. Grout width and tile terminations also change the measurements and the cost.
How much height does electric floor heating add?
In our experience, a traditional electric system needs at least a quarter inch and closer to a half inch once the membrane and mortar are installed. The roll-out mat we used is no thicker than a credit card.
Why does the finishing phase feel slower than rough work?
Many trades can work at the same time during rough installations which creates a lot of activity and energy. Finishing is sequential, careful work. So, it feels slower.